Christie Roadie HD+35K Manual do Utilizador descarregar pdf (Página 77)

Section 3: Operation

Roadie HD+35K User Manual 3-11

020-100340-02 Rev. 1 (01-2010)

Input 5 Key (OPT.1)

Press the INPUT 5 key to display from the INPUT 5 interface module installed in the Option 1 slot, which

typically is the standard factory-installed Dual SD/HD-SDI Module. If PIP is enabled, press INPUT 5 to

assign it as the PIP source. Note, if there are two inputs connected to this module, the second input (B) is

considered to be INPUT 7 and can be most easily accessed with INPUT 7. Or, if you are using the built-in

keypad or the optional "lite" remote, neither of which have a separate

INPUT key, use INPUT 5 to access

INPUT 7 as follows:

• While displaying from INPUT 5, press the

INPUT 5 key again. This switches to INPUT 7.

• While displaying from any input other than the Dual SD/HD-SDI Module, press the

INPUT 5 key. This

switches to either INPUT 5 or INPUT 7, depending on which of the Dual SD/HD-SDI Module inputs (A or

B) was last used. Press the

INPUT 5 key again to display from the other Dual SD/HD-SDI Module input.

Input 6 Key (OPT.2)

Press the INPUT 6 key to display from the INPUT 6 interface module installed in the Option 2 slot. If PIP is

enabled, press INPUT 6 to assign it as the PIP source. If the Dual SD/HD-SDI Module is installed here, and

there are two inputs connected, its second input (B) is considered INPUT 8 and can be most easily accessed

with

INPUT 8. Or, if you are using the built-in keypad or the optional "lite" remote, neither of which have a

separate

INPUT key, use INPUT 6 to access INPUT 8 as follows:

• While displaying from INPUT 6, press INPUT 6 again to switch to INPUT 8.

• While displaying from any input other than the Dual SD/HD-SDI Module, press

INPUT. This switches to

either INPUT 6 or INPUT 8, depending on which of the Dual SD/HD-SDI Module inputs (A or B) was last

used. Press

INPUT again to display from the other Dual SD/HD-SDI Module input.

Input Key (Standard IR Remote Only)

Press INPUT + n (where n = 1, 2, 3, 4, 5, or 6; 7 and 8 optional) as an alternative method for selecting which

source to display. Six source locations are identified with input numbers on the projector's input panel. The last

two, 7 and 8, require the Dual SD/HD-SDI Module installed in either of the option slots.

If PIP is enabled,

INPUT + n changes the PIP (secondary) image source, and INPUT + PIP + n changes the main

(primary) image source.

NOTE: The INPUT key behavior depends on whether or not the Display Channel List option is selected in the

Menu Preferences menu. You can choose to have on-screen feedback when you press INPUT, or you may

prefer to enter the desired source location "blind", i.e. without on-screen feedback. Refer to

Preferences.

Contrast Key

Press the CONT key on the standard IR remote to change the amount of white in your images. Use the UP

Arrow key or

DOWN Arrow key until you reach the desired level of white.

NOTE: For best results, start low and increase so that whites remain bright, but are not distorted or tinted, and

that light areas do not become white (i.e., "crushed"). Conversely, low contrast causes dim images. Refer

3.6.3 Image Settings Menu (Image Settings subsection).

Brightness Key

Press the BRIGHT key on the standard IR remote to increase or decrease the amount of black in the image. Use

LEFT and RIGHT Arrow keys until you reach the desired level of black. For best results, start high and decrease

so that dark areas do not become black (i.e., "crushed"). Conversely, overly high brightness changes black to

dark gray, and causes washed-out images.

Refer to 3.6.3 Image Settings Menu (Image Settings subsection).

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 191 192

Christie Roadie HD+35K Manual do Utilizador Página 77

Comentários a estes Manuais

Christie Roadie HD+35K Manual do Utilizador Página 77

Comentários a estes Manuais

Manuais e produtos relacionados com Projetores Christie Roadie HD+35K